PART OF CATALOG

ER-Spannzange mit Kuhlkanalen ER20 | 428ECC | < 15µm | O 7

42.00

Application:
For mounting straight-shank tools in collet chucks DIN 6499.


Note:
Only nominal size d can be clamped, with cooling channels. In order to achieve an optimum sealing the tool must be clamped on the complete length of the ground drill of the collet. (applicable up to 21 bar)

Angular milling cutter 90° 125mm – 40mm APKT 1604 / APHX 1604

455.00

  • For ISO Inserts APKT 1604... / APHX 1604...
  • With internal cooling
  • Nickel plated
  • Application in all materials
  • Delivery: without inserts

ER-Gewindebohrer-Spannzange IK ER16 | 426GA | < 15µm | 8 x 6,2

40.00

Application:
For machines with rigid tapping. For safe clamping of taps. Collets sealed with seal for IC.

Precision vice AVQ-160G/HV mechanical with mechanical booster

2,277.00

Construction:
- With mechanical booster - Clamping force preadjustable by graduation lines
- Clamping positions: horizontal, vertical and lateral
- The steel body is hardened and grinded all-round
- Integrated pull-down mechanism
- Bed height H: 0,01 mm


Delivery:

  • Instructions for use
  • Wrench
  • 4 pcs. vice clamps
  • 4 pcs. T-nuts 18 mm
  • Test certificate

3 point internal micrometer | digital 250-275mm | IP65 | reading 0,001mm

2,133.00

Construction:

  • Graduation: 0.001mm
  • Measuring contact points are designed to allow measurements near to the bottom of blind holes
  • reading parts brushed chromium-plated
  • Measuring surfaces are carbide
  • Ratchet stop

Delivery:

  • Extension
  • Warranty card
  • Instruction manual
  • Calibration certificate
  • LR44 1,5V Battery

    Setting ring not included in delivery - optionally available

Combi shell mill holder BT 50 – 16 – 160

157.00

Application:
For mounting milling cutters with transverse or longitudinal groove.

Delivery:
With retaining screw, driving ring and feather key


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

Milling arbors for screw-in cutters HSK 63 – M10 – 76 – LB50

188.00

Application:
For mounting screw-in cutters with thread.


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

End mill holder Weldon BT 40 – 06 – 50

47.00

Application:
For mounting straight-shank tools with lateral flat according to DIN 1835 form B (Weldon).


Delivery:
With clamping screw


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

FREE CONSULTATION

Have questions?
Leave a request