PART OF CATALOG

End mill holder Weldon SK 40 – 20 – 63

75.00

Application:
For mounting straight-shank tools with lateral flat according to DIN 1835 form B (Weldon).


Delivery:
With clamping screw


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

ER-Precision collet | stainless steel ER20 | 428ESP | < 5 µm | O 12,5 - 12

41.00

- Rustproof
- Stainless steel 1.4021 x 20Cr13
- HRC 43-47
- Longer-lived than standard collets
- Higher repeat-accuracy
- Maximum concentricity <0,005mm
- Honed collet boring
- Especially suitable fore wire EDM

ER-Collet chuck HSK 32 – 2/16 – 80 | ER 25 | Mini

130.00

Application:
For mounting straight-shank tools in collets.


Delivery:
With balanced clamping nut


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

KPS-Prazisionsspannzange abgedichtet KPS 16 | < 5µm | O 15,0

57.00

Application:
For mounting straight-shank tools in collet chucks KPS-system. To use for high speed cutting and high precision milling.

Morse taper adaptor SK 40 – 1 – 50

71.00

Application:
For clamping tools with Morse taper shank and thread according to DIN 228-1 form A.

With built-in tightening bolt


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

End mill holder Weldon with cooling channels SK 50 – 25 – 80

99.00

Application:
For mounting straight-shank tools with lateral flat according to DIN 1835 form B (Weldon).


Delivery:
With clamping screw and O-ring


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

ER-Gewindebohrer-Spannzange IK ER25 | 430GA | < 15µm | 4,5 x 3,4

44.00

Application:
For machines with rigid tapping. For safe clamping of taps. Collets sealed with seal for IC.

FREE CONSULTATION

Have questions?
Leave a request