Tapping chucks for synchronisation HSK 63 – M3-M12 – 93 | ER 16
Application:
For machining centres with synchronous spindle.
Note:
- Synchro tapping chucks compensate synchronisation errors.
- Minimal length compensation on compression and expansion balances very small pitch differences between synchro spindle and tap, which can cause high frictional forces on the thread flanks.
- A possible increase of axial force during the tapping process is reduced to a minimum.
- Suitable for internal coolant.
- Coolant pressure up to max. 100 bar.
- All holders are made of forged steel
- Specific, low warpage hardened
- Surface hardened HRC 58~60
- Hardening depth 0,8mm~0,9mm
- Taper angle tolerance < AT 3 according to DIN 2080
- Surface roughness Ra < 0,4 µm
- Tensile strength in the core of min. 800 N/mm? after DIN
- All functional surfaces fine machined
Cleaning propeller | Chip Blower O 16mm – 260mm
Version:
- Robust design
- Opening and closing of the flanks through the spindle speed control
- For use in any tool holder O16mm with a center coolant
- Body made of high strength and anodized aluminum
Advantages:
- Efficient cleaning of clamping equipment, pieces and tables
- Removal of chips und cleaning of water pockets
- Perfekte update to the automated work process
Drehzahlbereich (Empfehlung): Min. 5.000 / Max. 8.000 rpm
Rotationsrichtung: Uhrzeigersinn
Entfernung zwischen geoffneten Flugeln und Spahnen: 100~150 mm
Vorschub (Empfehlung): 3000~15.000 mm/min
Ideal fur mittlere Werkzeugmaschinen mit vielen und schwer zu entfernenden Spahnen
Zubehor/Ersatzteil:
Art.Nr.: ERS.900.90.260
Ersatz-Reinigungs-Propeller Typ 260mm
Lieferumfang:
1 Stk. Rotorblatt; Inklusive Feder, Positionier- und Halte-Pin
Morse taper adaptor BT 40 – 3 – 70
Application:
For mounting tools with Morse taper shank and tang according to DIN 228-1 form B.
- All holders are made of forged steel
- Specific, low warpage hardened
- Surface hardened HRC 58~60
- Hardening depth 0,8mm~0,9mm
- Taper angle tolerance < AT 3 according to DIN 2080
- Surface roughness Ra < 0,4 µm
- Tensile strength in the core of min. 800 N/mm? after DIN
- All functional surfaces fine machined
Clamping sleeves for taps DCONMS=20 | 12 x 9
Hydraulic expansion chuck BT 40 – 32 – 110
Application:
For mounting straight-shank tools acc. DIN 1835 form A+B+E and DIN 6535 form HA+HB+HE (larger than dia. 20 mm only with reduction sleeve).
Note:
l1 = max. clamping depth l2 = max. length adjustment range
Without wrench
- All holders are made of forged steel
- Specific, low warpage hardened
- Surface hardened HRC 58~60
- Hardening depth 0,8mm~0,9mm
- Taper angle tolerance < AT 3 according to DIN 2080
- Surface roughness Ra < 0,4 µm
- Tensile strength in the core of min. 800 N/mm? after DIN
- All functional surfaces fine machined
HSS-E spiral flute taps fine thread M12 9×7 P=1,25 DIN 374
Application:
- Thread configuration with a special design, prevents overfeeding, thin thread and pitch diameter oversize.
- Flute geometry with special design, better chip evacuation, prevents chip clogging, improves thread quality
- Excellent performance on various work material: Stainless steel, carbon steel, alloyed steel, tool steel
Have questions?
Leave a request
OUR PARTNERS
