PART OF CATALOG

Morse taper adaptor HSK 63 – 1 – 100

115.00

Application:
For clamping tools with Morse taper shank and thread according to DIN 228-1 form A.

With built-in tightening bolt


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

End mill holder Weldon BT 30 – 12 – 50

47.00

Application:
For mounting straight-shank tools with lateral flat according to DIN 1835 form B (Weldon).


Delivery:
With clamping screw


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

HSS-E spiral flute taps fine thread M5 3,5×2,7 P=0,5 DIN 374

16.00

Application:

  1. Thread configuration with a special design, prevents overfeeding, thin thread and pitch diameter oversize.
  2. Flute geometry with special design, better chip evacuation, prevents chip clogging, improves thread quality
  3. Excellent performance on various work material: Stainless steel, carbon steel, alloyed steel, tool steel

Drill chuck adaptor DIN 238 SK 30 – B16

52.00

Application:
For mounting drill chucks.



  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

Shell mill holder HSK 63 – 22 – 160

221.00

Application:
For mounting milling cutters with transversal groove.


Note:
d = 40/d = 60: For large diameter face mill cutters with four additional threaded holes according to DIN 2079.


SK 30 without coolant exit bores on the end face

Delivery:
With drivers, cross head retaining screw and cylinder head retaining screw for cutters with central coolant. For d = 60 only with four fi xation screws according to DIN 912.


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

Micrometer-Set | analogue | 0 – 300 12 pieces | reading 0,01mm

920.00

Construction:

  • Graduation: 0.01mm
  • Flatness: 0.6my
  • Carbide tipped measuring faces
  • Ratchet Stop

Delivery:

  • S-wrench, Standard (over 25mm range)
  • Warranty card
  • Instruction manual
  • Calibration certificat

OZ-Collet chuck SK 50 – 3/32 – 80 | OZ 32

108.00

Application:
For mounting straight-shank tools in collets.


Delivery:
With ball bearing clamping nut


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

FREE CONSULTATION

Have questions?
Leave a request