PART OF CATALOG

Morse taper adaptor MK 3 – MK 2

8.00

Application:
For mounting tools with Morse taper shanks.


Note:
Entirely hardened and grinded on the inside and outside

3 point internal micrometer | digital 62-75mm | IP65 | reading 0,001mm

785.00

Construction:

  • Graduation: 0.001mm
  • Measuring contact points are designed to allow measurements near to the bottom of blind holes
  • reading parts brushed chromium-plated
  • Measuring surfaces are carbide
  • Ratchet stop

Delivery:

  • Setting rings
  • Extension rod >6mm
  • Warranty card
  • Instruction manual
  • Calibration certificate
  • LR44 1,5V Battery

Hydraulic expansion chuck SK 50 – 18 – 110

441.00

Application:
For mounting straight-shank tools acc. DIN 1835 form A+B+E and DIN 6535 form HA+HB+HE (larger than dia. 20 mm only with reduction sleeve).


Note:
l1 = max. clamping depth l2 = max. length adjustment range


Delivery:
With wrench


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

Blade Micrometer | digital | 75 – 100 IP65

395.00

Construction:

  • Resolution: .00005" / 0.001mm
  • For measuring the groove diameter of shafts, keyways, and other hard to reach portions
  • Automatic On/Off to maximize battery life
  • Upon switching on the display will read the actual absolute measuring position
  • Inch/Metric conversion
  • Carbide tipped measuring faces
  • Non-rotating spindle
  • Ratchet stop

Delivery:

  • S-wrench
  • Standard (over 25mm range)
  • Warranty card
  • Instruction manual
  • Calibration certificate
  • LR44 1,5V Battery

End mill holder Weldon SK 40 – 08 – 130

73.00

Application:
For mounting straight-shank tools with lateral flat according to DIN 1835 form B (Weldon).


Delivery:
With clamping screw


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

Digital Caliper | 0-300mm with data output | reading 0,01mm

161.00

Construction:

  • Resolution: .0005" / 0.01mm
  • The caliper will be ready for measurements as soon as it is switched on with the LCD screen displaying the actual slider position
  • There is no need to set the zero position each time the caliper is used as the origin setting is retained even when the caliper is switched off
  • Inch/Metric conversion
  • Data output

Delivery:

  • Warranty card
  • Instruction manual
  • Calibration certificate
  • CR2032 3,0V Battery

Hydraulic expansion chuck HSK 63 – 10 – 85

290.00

Application:
For mounting straight-shank tools acc. DIN 1835 form A+B+E and DIN 6535 form HA+HB+HE (larger than dia. 20 mm only with reduction sleeve).


Note:
l1 = max. clamping depth l2 = max. length adjustment range


Delivery:
Without wrench


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

FREE CONSULTATION

Have questions?
Leave a request