PART OF CATALOG

Morse taper adaptor BT 40 – 4 – 110

89.00

Application:
For clamping tools with Morse taper shank and thread according to DIN 228-1 form A.


Delivery:
With built-in tightening bolt


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

End mill holder Weldon with cooling channels SK 50 – 20 – 100

110.00

Application:
For mounting straight-shank tools with lateral flat according to DIN 1835 form B (Weldon).


Delivery:
With clamping screw and O-ring


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

ER-Precision collet | stainless steel ER25 | 430ESP | < 5 µm | O 8,5 - 8,0

42.00

- Rustproof
- Stainless steel 1.4021 x 20Cr13
- HRC 43-47
- Longer-lived than standard collets
- Higher repeat-accuracy
- Maximum concentricity <0,005mm
- Honed collet boring
- Especially suitable fore wire EDM

End mill holder Weldon with cooling channels SK 50 – 14 – 160

167.00

Application:
For mounting straight-shank tools with lateral flat according to DIN 1835 form B (Weldon).


Delivery:
With clamping screw and O-ring


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

ER-Collet ER25 | 430E | < 15µm | O 10 - 9

11.00

Application:
For mounting straight-shank tools in collet chucks DIN 6499.


Note:
High flexibility: Large holding capacity up to –1 mm

HSSE twist drill 135° 4,8 mm DIN 338 | TIN coating

4.00

Note:
Particularly robust and strong due to strengthened core. Profile ground, with high concentricity.

Quick change tapping chuck SK 50 – M14-M36 – Gr.3

277.00

Application:
For the chucking of quick change adaptors for taps.


Note:
For machining centres with synchronous spindle.


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

Plug gauge | 13mm | H7 accuracy DIN 7162|7164 | size DIN 2245

29.00

Construction:

  • Hardened steel
  • Plug Gauge Accuracy according to DIN 7162/7164
  • Plug gauge sizes according to DIN 2245

Delivery:
Calibration certificate

FREE CONSULTATION

Have questions?
Leave a request