Tapping chucks for synchronisation BT 40 – M3-M33 – 115 | ER 40
Application:
For machining centres with synchronous spindle.
Note:
Synchro tapping chucks compensate synchronisation errors.Minimal length compensation on compression and expansion balances very small pitch differences between synchro spindle and tap, which can cause high frictional forces on the thread flanks.A possible increase of axial force during the tapping process is reduced to a minimum.Suitable for internal coolant.Coolant pressure up to max. 100 bar.
Delivery:
With balanced clamping nut
- All holders are made of forged steel
- Specific, low warpage hardened
- Surface hardened HRC 58~60
- Hardening depth 0,8mm~0,9mm
- Taper angle tolerance < AT 3 according to DIN 2080
- Surface roughness Ra < 0,4 µm
- Tensile strength in the core of min. 800 N/mm? after DIN
- All functional surfaces fine machined
Cleaning propeller | Chip Blower O 16mm – 260mm
Version:
- Robust design
- Opening and closing of the flanks through the spindle speed control
- For use in any tool holder O16mm with a center coolant
- Body made of high strength and anodized aluminum
Advantages:
- Efficient cleaning of clamping equipment, pieces and tables
- Removal of chips und cleaning of water pockets
- Perfekte update to the automated work process
Drehzahlbereich (Empfehlung): Min. 5.000 / Max. 8.000 rpm
Rotationsrichtung: Uhrzeigersinn
Entfernung zwischen geoffneten Flugeln und Spahnen: 100~150 mm
Vorschub (Empfehlung): 3000~15.000 mm/min
Ideal fur mittlere Werkzeugmaschinen mit vielen und schwer zu entfernenden Spahnen
Zubehor/Ersatzteil:
Art.Nr.: ERS.900.90.260
Ersatz-Reinigungs-Propeller Typ 260mm
Lieferumfang:
1 Stk. Rotorblatt; Inklusive Feder, Positionier- und Halte-Pin
Morse taper adaptor BT 50 – 5 – 100
Application:
For clamping tools with Morse taper shank and thread according to DIN 228-1 form A.
Delivery:
With built-in tightening bolt
- All holders are made of forged steel
- Specific, low warpage hardened
- Surface hardened HRC 58~60
- Hardening depth 0,8mm~0,9mm
- Taper angle tolerance < AT 3 according to DIN 2080
- Surface roughness Ra < 0,4 µm
- Tensile strength in the core of min. 800 N/mm? after DIN
- All functional surfaces fine machined
Clamping sleeves for taps with quick change DCONMS=25 | 9 x 7
Shell mill holder HSK 63 – 32 – 160
Application:
For mounting milling cutters with transversal groove.
Note:
d = 40/d = 60: For large diameter face mill cutters with four additional threaded holes according to DIN 2079.
SK 30 without coolant exit bores on the end face
Delivery:
With drivers, cross head retaining screw and cylinder head retaining screw for cutters with central coolant. For d = 60 only with four fi xation screws according to DIN 912.
- All holders are made of forged steel
- Specific, low warpage hardened
- Surface hardened HRC 58~60
- Hardening depth 0,8mm~0,9mm
- Taper angle tolerance < AT 3 according to DIN 2080
- Surface roughness Ra < 0,4 µm
- Tensile strength in the core of min. 800 N/mm? after DIN
- All functional surfaces fine machined
Ring gauge | 6mm ring gauge-accuracy DIN 2250
High Performance Milling Chuck HSK-A 100-32-105 DIN 69893 Form A HKS-system in wooden box
Have questions?
Leave a request
OUR PARTNERS
