3D-Taster analog 12mm Schaft
Der 3D-Taster besticht durch sein schlankes und attraktives Design. Seine prazisen und vielseitigen Einsatzmoglichkeiten erlauben schnelles und einfaches Ermitteln von Werkstucknullpunkten und Langenma?en.
Die Antastung ist in allen Achs-Richtungen (X/Y/Z) bei gleicher Zeigerauflosung moglich.
Sobald die Zeiger 0" anzeigen, steht die Spindelachse prazise auf der Werkstuckkante.
Der Schutz der Messeinheit steht im Vordergrund. Hierzu wurden gro?e Uberfahrwege in die Tasteinheit integriert. Diese sind durch mechanische Endanschlage begrenzt. Der Tasteinsatz hat eine Sollbruchstelle, die ganz weit oben angebracht ist. Sollte Ihr 3D-Taster durch au?ere Krafteinwirkung trotzdem beschadigt werden, so ist eine einfache Reparatur kostengunstig moglich.
Hinweis:
- not waterproof
- without test certificate
- without serial number
Shrink chuck 4,5° HSK 63 – 08 – 120
Application:
For mounting tools with straight shanks.
Note:
Toolholders suitable for induction-, contact- and hot air shrink units. O 3, 4, 5 with h4-tolerance and O 6 O 32 with h6-tolerance
For O 3, 4 and 5 mm only solid carbide tool shanks must be used!
- All holders are made of forged steel
- Specific, low warpage hardened
- Surface hardened HRC 58~60
- Hardening depth 0,8mm~0,9mm
- Taper angle tolerance < AT 3 according to DIN 2080
- Surface roughness Ra < 0,4 µm
- Tensile strength in the core of min. 800 N/mm? after DIN
- All functional surfaces fine machined
Morse taper adaptor BT 40 – 2 – 50
Application:
For clamping tools with Morse taper shank and thread according to DIN 228-1 form A.
Delivery:
With built-in tightening bolt
- All holders are made of forged steel
- Specific, low warpage hardened
- Surface hardened HRC 58~60
- Hardening depth 0,8mm~0,9mm
- Taper angle tolerance < AT 3 according to DIN 2080
- Surface roughness Ra < 0,4 µm
- Tensile strength in the core of min. 800 N/mm? after DIN
- All functional surfaces fine machined
Plug gauge | 50mm | H7 accuracy DIN 7162|7164 | size DIN 2245
End mill holder Weldon BT 50 – 18 – 160
Application:
For mounting straight-shank tools with lateral flat according to DIN 1835 form B (Weldon).
Delivery:
With clamping screw
- All holders are made of forged steel
- Specific, low warpage hardened
- Surface hardened HRC 58~60
- Hardening depth 0,8mm~0,9mm
- Taper angle tolerance < AT 3 according to DIN 2080
- Surface roughness Ra < 0,4 µm
- Tensile strength in the core of min. 800 N/mm? after DIN
- All functional surfaces fine machined
End mill holder Weldon with cooling channels BT 40 – 14 – 63
Application:
For mounting straight-shank tools with lateral flat according to DIN 1835 form B (Weldon).
Delivery:
With clamping screw and O-ring
- All holders are made of forged steel
- Specific, low warpage hardened
- Surface hardened HRC 58~60
- Hardening depth 0,8mm~0,9mm
- Taper angle tolerance < AT 3 according to DIN 2080
- Surface roughness Ra < 0,4 µm
- Tensile strength in the core of min. 800 N/mm? after DIN
- All functional surfaces fine machined
Have questions?
Leave a request
OUR PARTNERS
