PART OF CATALOG

Quick change adaptors without safety clutch Size 1 | 10 x 8

€16.00

Application:
For mounting taps. For right-hand and left-hand threads. Standard type without safety clutch.


Note:
Quick change adaptors without safety clutch can be interchanged, because only the shaft diameters and the squares must fit.

Blade Micrometer | digital | 0 – 25 IP65

€321.00

Construction:

  • Resolution: .00005" / 0.001mm
  • For measuring the groove diameter of shafts, keyways, and other hard to reach portions
  • Automatic On/Off to maximize battery life
  • Upon switching on the display will read the actual absolute measuring position
  • Inch/Metric conversion
  • Carbide tipped measuring faces
  • Non-rotating spindle
  • Ratchet stop

Delivery:

  • S-wrench
  • Standard (over 25mm range)
  • Warranty card
  • Instruction manual
  • Calibration certificate
  • LR44 1,5V Battery

Shrink chuck 4,5° HSK 100 – 25 – 160

€238.00

Application:
For mounting tools with straight shanks.


Note:
Toolholders suitable for induction-, contact- and hot air shrink units. O 3, 4, 5 with h4-tolerance and O 6 – O 32 with h6-tolerance


For O 3, 4 and 5 mm only solid carbide tool shanks must be used!
  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

HSS-E spiral flute taps fine thread M14 11×9 P=1,5 DIN 374

€24.00

Application:

  1. Thread configuration with a special design, prevents overfeeding, thin thread and pitch diameter oversize.
  2. Flute geometry with special design, better chip evacuation, prevents chip clogging, improves thread quality
  3. Excellent performance on various work material: Stainless steel, carbon steel, alloyed steel, tool steel

Shell mill holder SK 40 – 40 – 50

€72.00

Application:
For mounting milling cutters with transversal groove.


Note:
d = 40/d = 60: For large diameter face mill cutters with four additional threaded holes according to DIN 2079.


SK 30 without coolant exit bores on the end face

Delivery:
With drivers, cross head retaining screw and cylinder head retaining screw for cutters with central coolant. For d = 60 only with four fi xation screws according to DIN 912.


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

Hydraulic expansion chuck 40 – 12 – 60

€580.00

Application:
For mounting straight-shank tools acc. DIN 1835 form A+B+E and DIN 6535 form HA+HB+HE (larger than dia. 20 mm only with reduction sleeve).


Note:
l1 = max. clamping depth l2 = max. length adjustment range


Delivery:
With wrench

Reduction sleeves for Milling Chuck DCONMS=20 | DCONWS=5

€34.00

Application:
For mounting tools with straight shanks.


Note:
The chucking diameter is configured for a tool tolerance of h6.

End mill holder Weldon SK 40 – 12 – 50

€47.00

Application:
For mounting straight-shank tools with lateral flat according to DIN 1835 form B (Weldon).


Delivery:
With clamping screw


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

FREE CONSULTATION

Have questions?
Leave a request