PART OF CATALOG

Shell mill holder BT 30 – 27 – 40

106.00

Application:
For mounting milling cutters with transversal groove.


Note:
d = 40/d = 60: For large diameter face mill cutters with four additional threaded holes according to DIN 2079.


SK 30 without coolant exit bores on the end face


Delivery:
With drivers, cross head retaining screw and cylinder head retaining screw for cutters with central coolant. For d = 60 only with four fi xation screws according to DIN 912.


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

Pull studs ISO 7388-3 | Form JD | M16 | 45° | with drill through | incl. O-ring

8.00

ISO 7388-3 - Retention knobs for shank form JD with centric inner cooling supply

Application:

  • For tools with taper shanks DIN 69871 and JIS B 6339 (MAS-BT)
  • In machining centres (machines with automatic tool changers)
  • In NC machines (machines without automatic tool changers)




Milling arbors for screw-in cutters HSK 63 – M16 – 176 – LB150

272.00

Application:
For mounting screw-in cutters with thread.


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

Shrink chuck 4,5° PSK 40 – 12 – 75

324.00

Application:
For mounting tools with straight shanks.


Note:
Toolholders suitable for induction-, contact- and hot air shrink units. O 6 – O 32 with h6-tolerance


For O 3, 4 and 5 mm only solid carbide tool shanks must be used!
  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

ER-Precision collet ER25 | 430EP | < 5µm | O 12 - 11

25.00

Application:
For mounting straight-shank tools in collet chucks DIN 6499. To use for high speed cutting and high precision milling.


Note:
High flexibility: Large holding capacity up to –1 mm

Blade Micrometer | digital | 0 – 25 IP65

321.00

Construction:

  • Resolution: .00005" / 0.001mm
  • For measuring the groove diameter of shafts, keyways, and other hard to reach portions
  • Automatic On/Off to maximize battery life
  • Upon switching on the display will read the actual absolute measuring position
  • Inch/Metric conversion
  • Carbide tipped measuring faces
  • Non-rotating spindle
  • Ratchet stop

Delivery:

  • S-wrench
  • Standard (over 25mm range)
  • Warranty card
  • Instruction manual
  • Calibration certificate
  • LR44 1,5V Battery

Shell mill holder SK 50 – 60 – 70

148.00

Application:
For mounting milling cutters with transversal groove.


Note:
d = 40/d = 60: For large diameter face mill cutters with four additional threaded holes according to DIN 2079.


SK 30 without coolant exit bores on the end face

Delivery:
With drivers, cross head retaining screw and cylinder head retaining screw for cutters with central coolant. For d = 60 only with four fi xation screws according to DIN 912.


  • All holders are made of forged steel
  • Specific, low warpage hardened
  • Surface hardened HRC 58~60
  • Hardening depth 0,8mm~0,9mm
  • Taper angle tolerance < AT 3 according to DIN 2080
  • Surface roughness Ra < 0,4 µm
  • Tensile strength in the core of min. 800 N/mm? after DIN
  • All functional surfaces fine machined

 

 

FREE CONSULTATION

Have questions?
Leave a request