Tapping chucks for synchronisation 20 – M3-M10 | ER 16 | Mini
Application:
For machining centres with synchronous spindle.
Note:
- Synchro tapping chucks compensate synchronisation errors.
- Minimal length compensation on compression and expansion balances very small pitch differences between synchro spindle and tap, which can cause high frictional forces on the thread flanks.
- A possible increase of axial force during the tapping process is reduced to a minimum.
- Suitable for internal coolant.
- Coolant pressure up to max. 100 bar.
Ring gauge | 2,5mm ring gauge-accuracy DIN 2250
Milling arbors for screw-in cutters BT 50 – M16 – 188 – LB150
Application:
For mounting screw-in cutters with thread.
- All holders are made of forged steel
- Specific, low warpage hardened
- Surface hardened HRC 58~60
- Hardening depth 0,8mm~0,9mm
- Taper angle tolerance < AT 3 according to DIN 2080
- Surface roughness Ra < 0,4 µm
- Tensile strength in the core of min. 800 N/mm? after DIN
- All functional surfaces fine machined
Cleaning propeller | Chip Blower O 16mm – 260mm
Version:
- Robust design
- Opening and closing of the flanks through the spindle speed control
- For use in any tool holder O16mm with a center coolant
- Body made of high strength and anodized aluminum
Advantages:
- Efficient cleaning of clamping equipment, pieces and tables
- Removal of chips und cleaning of water pockets
- Perfekte update to the automated work process
Drehzahlbereich (Empfehlung): Min. 5.000 / Max. 8.000 rpm
Rotationsrichtung: Uhrzeigersinn
Entfernung zwischen geoffneten Flugeln und Spahnen: 100~150 mm
Vorschub (Empfehlung): 3000~15.000 mm/min
Ideal fur mittlere Werkzeugmaschinen mit vielen und schwer zu entfernenden Spahnen
Zubehor/Ersatzteil:
Art.Nr.: ERS.900.90.260
Ersatz-Reinigungs-Propeller Typ 260mm
Lieferumfang:
1 Stk. Rotorblatt; Inklusive Feder, Positionier- und Halte-Pin
KPS-Collet chuck SK 50 – 1/10 – 165 | KPS 10
Application:
For mounting straight-shank tools in collets. To use for high speed cutting and high precision milling.
Delivery:
With balanced clamping nut
- All holders are made of forged steel
- Specific, low warpage hardened
- Surface hardened HRC 58~60
- Hardening depth 0,8mm~0,9mm
- Taper angle tolerance < AT 3 according to DIN 2080
- Surface roughness Ra < 0,4 µm
- Tensile strength in the core of min. 800 N/mm? after DIN
- All functional surfaces fine machined
Shrink chuck 4,5° HSK 50 – 10 – 85
Application:
For mounting tools with straight shanks.
Note:
Toolholders suitable for induction-, contact- and hot air shrink units. O 3, 4, 5 with h4-tolerance and O 6 O 32 with h6-tolerance
For O 3, 4 and 5 mm only solid carbide tool shanks must be used!
- All holders are made of forged steel
- Specific, low warpage hardened
- Surface hardened HRC 58~60
- Hardening depth 0,8mm~0,9mm
- Taper angle tolerance < AT 3 according to DIN 2080
- Surface roughness Ra < 0,4 µm
- Tensile strength in the core of min. 800 N/mm? after DIN
- All functional surfaces fine machined
Have questions?
Leave a request
OUR PARTNERS
